February 25 , 2008 - The Sheet Rolling Operating Committee (SROC) met during their Specialty Conference, “Hot Rolling Fundamentals — A Practical Training Seminar,” on Feb. 25 in Orlando, Fla. The first order of business was the SROC sessions for AISTech 2008. This involved filling a couple open time slots and finalizing the session chairs. The committee also reviewed and approved the SROC topics for the Call for Papers for AISTech 2009, which will be held in St. Louis, Mo. This was followed by a review of the first day of the Training Seminar. The general consensus was that the first day was very successful, with lots of interaction between the presenters and the attendees. This conference was a joint effort between the SROC and representatives from the AISI Hot Strip Mills Manufacturing Committee. With the upcoming integration of the AISI committees into AIST, there was some discussion about how these training seminars will be handled after the integration, since there will be a Hot Sheet Rolling committee and a Cold Sheet Rolling committee. Since contracts have already been signed for the 2009 Training Seminar, this group will work with the new Cold Sheet Rolling committee to ensure this training program continues. The AISI Hot Strip Mill Committee met on Feb. 14 in Columbus, Miss., and an update on the integration discussion from that meeting was provided by Tom Weiler and Bill Albaugh, who both attended. There was also additional discussion on the status of the integration. To maintain the momentum of these committees, it was also decided that the AISI Hot Strip Mills committee will proceed with its meeting already scheduled for June. In addition, representatives from each organization’s committee may meet in the future to assist in the transition to the new structure.

October 10-12 , 2007 - The Cranes Operating Committee (COC) and Sheet Rolling Operating Committee (SROC) held a joint meeting in Concord, Calif., on Oct. 10–12. The meeting kicked off with a tour of the rolling facilities at USS-POSCO. The tour began with the pickle line, progressed through the galvanizing and tinplating lines, and ended at the USS-POSCO Learning Center for technical presentations. The technical presentations were as follows: “Double Cold Reduction Mill Conversion Project at USS-POSCO” by Dean Broglie, USS-POSCO; “Pickle Line Improvements at USS-POSCO” by Jesus Partida, USS-POSCO; “Controlled Area Network for EOT Cranes” by Jeremy Pearson, Cattron-Thiemeg; “Crane Bumpers and End Stops for EOT Cranes” by Charlie Bowers, Cavotec; “Crane Rail Size Availability” by Chip Miller, L.B. Foster; and “U. S. Steel–Gary Works Westside EOT Crane Inspection Program” by Andrew Montalbano, U. S. Steel–Gary Works. Following the technical presentations, the COC adjourned for the day. The SROC remained to review and organize abstracts into four technical sessions for AISTech 2008, focusing on hot and cold rolling and surface inspection. Volunteers were also identified as chairs for these sessions.

On Oct. 12, the COC held a business meeting, beginning with a review of the outline created for a Maintenance, Inspection and Repair Guide for EOT Cranes Users. This guide will examine inspection practices and repair criteria for crane- and runway-associated components, in an effort to develop consistent guidelines on maintenance and when to repair and/or replace these components to enhance crane operation and safety, and to minimize unplanned downtime through improved reliability. Each section of the guide will be reviewed by individual working groups, who will organize and write an outline for that section. Also discussed was the 2008 AIST Crane Symposium, scheduled for June 1–3, in Pittsburgh, Pa. A survey of the 2007 Crane Symposium attendees led to the development of a list of presentation topics for the 2008 symposium. Potential presenters were indentified and will be contacted in the coming months to confirm their participation. Also discussed was the viability of an International Crane Symposium, which would be held in Košice, Slovakia, in 2008. It was determined that, to provide adequate planning for such an event, the event should be scheduled for the fall of 2008. Finally, volunteers were taken to present at the COC technical session at AISTech 2008. The next meeting is tentatively scheduled for Jan. 16–17, 2008, in Memphis, Tenn., with a tour of Nucor-Yamato Steel.

On Oct. 12, the Sheet Rolling Operating Committee (SROC) held a business meeting, first discussing plans for their AISTech 2008 technical sessions. They reviewed the status of the Hot Rolling Training Seminar, which will be held Feb. 24–28, 2008, in Orlando, Fla. They also discussed preplanning for a 2009 AIST Cold Rolling Training Seminar. The SROC began organizing members to complete a North American Hot Strip Mill Roundup to benchmark these facilities for publication in Iron & Steel Technology. They discussed several options for future meetings and started to develop a plan to get more participation from producer members. A review of the presentations for the Hot Rolling Training Seminar was to be held in November to ensure elimination of any overlap between presentations. The SROC also planned to hold a meeting during the Hot Rolling Training Seminar in February.

July 11-12, 2007 - The Hot Rolling Training Seminar Task Force of the Sheet Rolling Operating Committee met July 11–12 in Toledo, Ohio, along with representatives from AISI, to continue planning the Hot Rolling Training Seminar, which will be offered Feb. 24–29, 2008, in Orlando, Fla. An update on the status of tasks assigned during the previous meeting was provided, followed by a review of comments from members of either association. The attendees then reviewed the individual sections of the previous course to ensure complete coverage of pertinent topics and to eliminate redundancy. There was also discussion on whether roll bite lubrication should be covered in the upcoming conference. It was decided that the workbook would also be provided on a CD-ROM this year. Brendan Brophy was selected as the committee representative who, beginning with the second morning of the course, would tie in presentations from the previous day with the upcoming presentations to provide continuity in the course. The presenter guidelines were modified to include a timeline that permits the Task Force to review the presentations prior to the conference. To ensure that the attendees have the opportunity to get specific questions answered, cards will be available for them to submit their questions. A letter was also drafted that will be sent out to past presenters to thank them for their participation.

May 8, 2007 - The Sheet Rolling Operating Committee (SROC) met on May 8 in Indianapolis, Ind., in conjunction with AISTech 2007. The first item of business was a review of the SROC mission statement: “Promote advancement in sheet and strip rolling technologies and operating practices through information exchange and training.” The members agreed that this still served the purposes of the committee. This was followed by the election of officers for the upcoming year. Brendan Brophy was elected chair; Eric Thokar, vice chair; and Charles Varga, papers chair. Plans for the committee’s future Specialty Conferences were discussed, and Mr. Brophy updated the members on the status of the upcoming Hot Rolling Training Seminar, to be held Feb. 24–29, 2008, in Orlando, Fla. This is a collaborative effort with the American Iron and Steel Institute (AISI). The groups improved the quality of this course by eliminating areas of duplication and ensuring complete coverage in other areas. The SROC also discussed the reviews of their most recent Cold Rolling Training Seminar (held in February 2007) and the plans for the next offering. Mr. Thokar recommended that the committee prepare hot mill and cold mill roundups that could be included in Iron & Steel Technology, and he agreed to chair the subcommittee to initiate this effort, beginning with the hot mill roundup. The need for training on process lines was then covered, and the committee planned to meet with the Coating and Process Lines Operating Committee (CPLOC) to advance this training. Mr. Brophy then updated the group on his participation in the 2006 AIST Leadership Conference, referencing the report generated for this meeting, which provided helpful tips for running committee meetings and recruiting new members. Locations for upcoming SROC meetings were discussed, and all members were asked to give thought to topics for technical discussions at these meetings.

April 4-5, 2007 - The Hot Rolling Training Seminar Task Force of the Sheet Rolling Operating Committee met on April 4–5 at Severstal NA in Detroit, Mich., to work on the upcoming conference that will be held in Orlando, Fla., Feb. 24–28, 2008. This task force is comprised of members of the AIST Sheet Rolling Operating Committee and the AISI Hot Rolling Committee as a collaborative effort. Members from both organizations reviewed the material from the last time this conference was offered, with an eye toward minimizing overlap in presentations and ensuring that all main areas are adequately covered. Workbooks and presentations from both the AIST course and the AISI course were reviewed to try to meld the best of both offerings. After a general review of the evaluations and outlines from past conferences, the members went through each presentation. Presenters for the conference were identified, and task force members were assigned to communicate with the presenters.

February 19, 2007 - The Sheet Rolling Operating Committee (SROC) met in Orlando, Fla., on Feb. 19 in conjunction with their Specialty Conference, “Cold Rolling Fundamentals — A Practical Training Seminar.” During this meeting, the status of the Sheet Rolling technical sessions for AISTech 2007 in Indianapolis, Ind., was reviewed, and last-minute items such as papers and session chairs were finalized. This meeting was held at the conclusion of the first day of the training seminar, so a review of the conference’s opening day was held. The feedback regarding the opening sessions was very positive. The next agenda item was a discussion on future training seminars. Since there remains in the industry a need for this type of training, the committee will continue with a plan of alternating cold rolling and hot rolling training seminars. The Hot Rolling Training Seminar is currently being refined, to be offered in 2008. The refinement of this conference is a collaborative effort between this committee and the AISI Hot Strip Mills Committee. The SROC also discussed upcoming meeting plans to ensure that each meeting offers something of value to those attending. This can be along the lines of a plant tour, a technical presentation at the meeting or other opportunities for exchange of information.

January 22-23, 2007 - The Sheet Rolling Operating Committee (SROC) met in Toledo, Ohio, on Jan. 22–23. Jeff Jackson welcomed everyone to the meeting on Jan. 22. This was followed by a review of the SROC sessions for AISTech 2007, including session titles and chairs. After this was finalized, an update was provided on the upcoming Cold Rolling Training Seminar. Since several presenters were new to the course, the committee planned to review the presentation material. Several representatives from the American Iron and Steel Institute (AISI) were also at the meeting as part of a collaborative effort between the two committees on another seminar, the Hot Rolling Training Seminar, last offered in 2006. These groups plan to jointly review the course material and the feedback, and then work to refine the course and avoid any overlap for the next offering in 2008. A task force with members from both organizations was identified to accomplish this. Ian Ward, senior operations engineer for North Star BlueScope Steel, gave a technical presentation on sideguide calibration. This was followed by an update from the attendees on activities within their companies. The following morning, Ray Peters, vice president — operations for North Star BlueScope Steel, gave a presentation on BlueScope’s role in North Star BlueScope and an overview of steel activities in Australia and Asia. The meeting concluded with a tour of the meltshop and hot mill at North Star BlueScope Steel.

May 3, 2006 - The Sheet Rolling Operating Committee met on May 3 in Cleveland, Ohio, during AISTech 2006. The committee began the meeting by electing officers for the upcoming year. It was then decided that a subcommittee will plan technical sessions for AISTech 2007, and volunteers stepped up to spearhead this effort. Volunteers also came forth to participate in improving the committee’s training seminars on hot and cold rolling, which are held biennially on alternating years. A general comment was made that Brendan Brophy had made a well-received safety presentation at a recent meeting. Other ideas that will spark interest would be appreciated. Skinpass and temper mill operations are still of interest and should be included in one of the committee’s upcoming meetings. They also planned to review the status of a Process Lines Training Seminar and to determine, along with the Coating and Process Lines Operating Committee, if this training will be offered in the future.

February 20, 2006 - The Sheet Rolling Operating Committee met in Orlando, Fla., on Feb. 20, 2006, in conjunction with the Hot Rolling Training Seminar, which they sponsored. The meeting was held at the conclusion of the first day of the Specialty Conference. The discussion began with a review of the first day of the training seminar and an outlook on the balance of the week. One of the goals was to have two committee members review the course and make recommendations to minimize overlap of the topics the next time the course is offered. Ideas for fine-tuning the Cold Rolling Training Seminar, scheduled for February 2007, were also discussed. The sheet rolling sessions for AISTech 2006 were reviewed, and several members of the committee were identified as session chairs. Also discussed was the need for a process lines training seminar, based on a course developed previously. The general consensus was that this course should be a product of the Coating and Process Lines Operating Committee, but it was uncertain whether that committee is interested in refining the course. If the CPLOC does not make plans to offer this course after discussing it at their next meeting, the SROC would be interested in refining it. The SROC’s upcoming meeting schedule was also reviewed, and topics for technical discussion at these meetings were identified.             

October 12-13, 2005 - The Sheet Rolling Operating Committee met Oct. 12–13 in Ontario, Calif. An update on the status of the committee’s technical sessions for AISTech 2006 was provided, and it was agreed to pursue joint sessions with other Operating Committees. An update on the status of the Hot Rolling Training Seminar followed. Some minor modifications were made to the schedule, and replacement presenters were identified where necessary. Chairs and reviewers were also identified for this conference, which will be held Feb. 20–23 in Orlando, Fla. A discussion on the format for future meetings was held, with plans made to handle program planning in smaller groups and to hold a round table each year. A tour of California Steel followed, and the attendees visited the temper mill, annealing, hot mill, roll shops and the 5-stand cold mill. The next day, an overview presentation of North Star BlueScope was provided, with an emphasis on safety drivers, followed by an open discussion.